CAPACITIES

PRODUCTION

• 60 loads per hour, based on load configuration and machine options

LOAD WEIGHT

• 4,000 lbs. maximum, with pallet bottom boards, running perpendicular to conveyor rollers.
• *Load stability may require softstart / softstop through optional variable frequency drive.

APPROXIMATE SHIPPING WEIGHT

• 4,734 lbs

MACHINE DIMENSIONS

• 198"W x 137"L x 102"H.

LOAD SIZE

• Min. 36"W x 36"L x 20"H.
• Max. 50"W x 50"L x 80"H.

ELECTRICAL REQUIREMENTS

• 230V/3/60 20AMPS
• (other voltages available upon request).

PNEUMATIC REQUIREMENTS

• 3CFM @ 80 PSI comes with FRL (Filter, Regulator, Lubricator)

CONTROLS

• Allen Bradley 5/03 PLC.
• Allen Bradley touch screen operator interface.
• 24V control system.
• Current overload protection.
• Autoheight sensing photoeye with On/Off switch.
• Power On/Off lockable switch and indicator light.
• Three emergency stop stations.
• Separate up and down carriage speeds.
• Separate top and bottom wrap selectors (0-9).
• Film force to load control.
• Visual film break alarm.
• Manual clamp jog- Reset button.
• Manual function for table Fwd/Rev., carriage Up/Down, and on all three sections of conveyor Fwd/Rev.
• Alarm mode diagnostic with 15 different alarms.
• Positive turntable home position braking system.
• Indicator light for all operations.
• Air pressure switch- Double brush dust tight slip ring.
• Depending upon system design and options, other controls may be required.

FILM DELIVERY SYSTEM

• 20" NO-THREAD™ Powered Pre-Stretch Carriage.
• 1/2 HP AC motor with variable frequency drive.
• 50-300% pre-stretch ratio (preset to customer spec. Std 200%).
• Electronic film tension control with analog sensor.
• Sensing device for film out/broken.
• Lexan roller cover.
• Film force release for easy pull at start and end of cycle.

FILM CARRIAGE DRIVE

• 3/4 HP AC motor with variable frequency drive.
• Two #50 chain carriage lifts for safety.
• Dual ½” CRS ways with UHMW-PE carriage glides

FILM TAIL TREATMENT

• Automatic film clamping/cutting.
• Pulsed controlled cutter.
• Film alignment arm.
• Brush-on film tail treatment.

TURNTABLE DRIVE

• Max. 15 RPM variable speed.
• 1-1/2 HP AC motor with variable frequency drive.
• Heavy duty Ring Gear Bearing drive.
• Electronic softstart / softstop.
• Positive turntable alignment controlled by proximity sensor.
• Electric brake

TURNTABLE CONVEYOR

• 77" dia. 1/2" steel plate.
• 2-1/2" dia. rollers on 3" centres.
• 1/8" wall cold rolled electric welded steel rollers.
• All rollers driven (including all surround rollers).
• 52” BFR (between frame rails).
• 3/4 HP AC motor with variable frequency drive.
• Electronic softstart / softstop.
• #40 chain drive with contour driven rollers.
• Heavy duty cast iron flange mounted bearing.

CONVEYOR

• 5' in / 5' out powered contoured conveyor.
• Standard: Pass height 18”. * other pass heights available.
• 1/8" wall cold rolled electric welded steel rollers.
• 2-1/2" dia. rollers on 3" centres.
• 52” BFR (between frame rails).
• All rollers driven via #40 chain.
• 3/4 HP AC motor with variable frequency drive including Fwd/Rev manual jog.
• Heavy duty structural steel design.
• Heavy duty cast iron flange mounted bearings.
• Up to 35 feet per minute, *other speeds available
• *Additional conveyors and other types available upon request.

STRUCTURE

• Formed steel tower consisting of 11 gauge front section and 14 gauge back cabinet section with lockable door.
• Forklift portable base design (from both ends).
• Heavy duty structural steel construction.
• Lag bolt brackets to secure machine to the floor.

TECHNICAL INFORMATION

The machine is provided with a manual including:

• Electro/mechanical schematics and drawings.
• Troubleshooting guide.
• Installation instructions.

WARRANTY

• All Wulftec-automatic machines come with a three-year warranty.
• All ring gear bearings are warranted for ten years.
• All Wulftec pre-stretch compound rollers have a lifetime warranty.